I’m using an nspire CX-CAS revision I, and of course OS 3.6. I’ve been using ndless 3.6 since it came out, but recently, I’ve been having weird problems when ndless is installed. A NAND corruption (generally caused by a Nover overclocking without following its recommandations).There are at the time of writing no strong relations between these rare failures and Ndless. The TI-Nspire is stuck with a system error at boot time Now try to open the maintenance menu and follow the procedure above ( “The TI-Nspire CX falls into a reboot loop”).Exit the diags tool by pressing the Reset button at the back of the calculator (there’s not exit option in the menus).Wait for the battery to reach a level of 30%.Choose the option to run the battery tests. Hold the the following keys at boot time: Esc+Menu+Minus.You then can’t open the maintenance menu as suggested above. The TI-Nspire CX falls into a reboot loop and ran out of battery Option ‘4’ (complete format) will also do, but will also delete all your documents. Select ‘2’ to uninstall the current OS.If the maintenance menu displays the message “ Replace the battery and try again“, see below “The TI-Nspire CX falls into a reboot loop and ran out of battery”.with the TouchPad keypad or the CX: Doc+Enter+EE then ON.with the ClickPad keypad: Home+Enter+P then ON.Enter the maintenance menu by turning it on while holding the following keys until half the progress bar:.Reboot the TI-Nspire, by unplugging the USB cable, then removing and putting back a battery on classic TI-Nspire or by pressing the reset button on TI-Nspire CX.Note that HW-S models are not compatible with OS 3.6, OS >= 3.9.1 is required. You can find your hardware revision on the back of the calculator (the last letter). The TI-Nspire falls into a reboot loopįollow Flyingraijin2013’s video tutorial or the procedure below to uninstall the OS/format your TI-Nspire. It should confirm there is a problem (GPIO error) and will fix it when a key is pressed. Hold Esc+Menu+Minus (Minus near Plus) while pressing the ‘reset’ button to launch the Diagnostic software. This issue is not related to Ndless and may happen on a never-Ndlessed TI-Nspire. You must reinstall it after each reset The calculator freezes on boot up with a black and white screen The installation of Ndless is indeed not reboot-proof. After a reset Ndless is not installed anymore Running an executable from the documents screen displays “Sorry. Reset the calculator by pressing the button under it, and retry the installation procedure. The current version (v3.6) of Ndless makes these instabilities difficult to fix, sorry for the annoyance. On some calculators the state of the USB connection may change the installation success rate. Try to reinstall Ndless with the USB cable plugged in or unplugged. The TI-Nspire reboots when the scratchpad/a document is opened ![]() Reinstall OS 3.9.1 and install Ndless 3.9. One of the side effects is not to be able to use the TI-Nspire without connecting it. HW-S models are not compatible with OS 3.6, OS >= 3.9.1 is required. You can find your hardware revision on the back of the calculator (the last letter, see above). ![]() ![]() The TI-Nspire turns off when not connected to a computer You are opening ndless_installer and plugging the calculator to a computer or another TI-Nspire.You have transferred all the following files to your TI-Nspire in a top-level folder named ‘ ndless‘: ndless_installer.tns, ndless_resources_3_9_1.tns and.OS 3.9.1 is installed on your TI-Nspire.OS >= 3.9.1 is required. You can find your hardware revision on the back of the calculator (the last letter).įor Ndless 3.6 : Recommended for hardware = HW-S Note that HW-S models are not compatible with Ndless 3.6 / OS 3.6. You can post a message to ask for help if you can’t find what’s wrong with your installation. This guide helps you to determine and solve problems encountered when installing Ndless v3.6 or Ndless v3.9.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |